Blackout curtains are both convenient and stylish. Therefore, they can both be beneficial and enhance your room’s look. Moreover, you can modify blackout curtains according to your choice.
But sometimes, blackout curtains get creases or wrinkles. You might have installed blackout curtains and don’t know how to get creases or wrinkles. Many methods are available to get wrinkles out of blackout curtains. It depends on you which method you want to follow.
How to get creases or wrinkles out of blackout curtains?
The simplest way to get creases or wrinkles out of blackout curtains is to iron the blackout curtains. You can also use a fabric steamer on the curtains to keep them straight. Moreover, you can also put the blackout curtains into the washing machine and dryer. You can follow one of these methods.
Table of Contents
If your blackout curtains get creases or wrinkles, they will not look good. Moreover, they will decrease the stylish appearance of the room. So, you need to get the wrinkles out of blackout curtains.
Iron:
You can iron the blackout curtains carefully to remove the wrinkles. But sometimes, iron can damage the fabric. So, you have to be careful about which fabric blackout curtains are made of and how much heat to provide. Sometimes, the iron automatically controls the temperature. So, you need to notice simply.
Steaming:
You can also use a fabric steamer to remove creases or wrinkles out of blackout curtains. Using fabric steamer is pretty easy. You need to fill the steamer with water and slowly put steam over the curtains from top to bottom. Gradually, you will see the curtains are straightening.
Dryer:
You can use a dryer to remove creases or wrinkles from the blackout curtains. Put the blackout curtains on the dryer with a wet towel or cloth. Use a permanent press cycle. You can also wash the blackout curtains in the washing machine before putting them on the dryer.
Can blackout curtains be ironed?
Yes, blackout curtains can be ironed. Sometimes, blackout curtains get wrinkles or creases that make the curtains look bad. So, you need to iron the curtains to get the wrinkles out of the curtains.
When you iron the blackout curtain, you need to keep the temperature of the iron low. If you have to use high temperature, you can put a cloth between the curtain and the iron so that the curtains don’t burn.
You can also spray some water on the curtain and slowly iron the curtain to remove stubborn wrinkles. But you have to keep the heat low.
How to iron blackout curtains?
You can iron blackout curtains to get any crease or wrinkle out of the curtains. But you can’t iron them as random clothes. You have to be careful and follow a process to iron blackout curtains. You can follow the mentioned process.
- At first, set the iron table and place an aluminum foil on it.
- Keep the blackout curtains on the aluminum foil and keep the foamed side in the bottom.
- On top of the curtains, put a thin cloth or bed sheet.
- Iron over the cloth with low heat. Don’t raise the heat over the average heat.
- Iron small area at a time. Once ironed that area, move to the next.
- After finishing ironing, hang the blackout curtains on the windows. Otherwise, the curtains will get wrinkles.
Can I steam iron blackout curtains?
Yes, you can steam iron blackout curtains. Steaming is the traditional way to straighten the blackout curtains. For steam ironing, you have to warm up the iron to an average temperature suitable for the fabric.
Then you have to put steam on the fabric with a cloth steamer. Straighten up the curtains with your hand before steaming. After putting steam, glide the iron on the fabric from one upward to downward. You should not iron the insulating or foamed side.
In the whole process, you need to keep the heat of the iron low. Otherwise, it can burn the fabric. After steam ironing, you will see the wrinkles go away. So, steam ironing is an effective way to straighten blackout curtains.
How to get wrinkles out of polyester blackout curtains?
If you want to get wrinkles out of blackout curtains, you can iron, steam, or dry out the curtains. But when it comes to polyester fabric, you might be confused about how you can get wrinkles out of polyester blackout curtains. But you can also iron polyester blackout curtains. Let’s see how you can do it.
- Set up the iron table and place an aluminum foil on it.
- Put the blackout curtains over the aluminum foil, and don’t iron the foamed side directly.
- Put a cloth or bed sheet over the curtains and set the iron’s heat to the “Polyester” setting.
- Iron the cloth with the specific heat. Don’t raise the heat over the specific heat, and the curtains will get the heat gradually.
- Don’t iron a broad area at a time. Once ironed a small area, move to the next.
- Hang the blackout curtains to the place before they get any fresh wrinkles.
How do you get wrinkles out of curtains without an iron?
Ironing is one of the simplest ways to get wrinkles out of curtains. But you can also remove wrinkles without an iron. You can follow some methods if you don’t want to iron the curtains.
Steaming:
Steaming is another simple way to get wrinkles out of curtains. You can use a cloth steamer to put steam on the curtains. Provide steam from upward to downward and keep the curtain straight. Gradually, the curtains will be wrinkle-free.
Dryer:
You can also use a dryer to get out of wrinkles from curtains. Keep the curtains in the dryer with a wet towel or cloth. You can use a permanent press cycle. After a couple of hours, you will see the curtains wrinkle-free.
Humidity:
You can use the humidity process to get the simple wrinkles out of the curtains. Hang the curtains in the bathroom. Turn on the hot shower and after some time, turn off the hot shower.
Close the door of the bathroom and let the steam spread on the curtains. After some hours, you will see the wrinkles go away. Humidity will work here to straighten the curtains.
Does wrinkle release spray work on curtains?
Yes, wrinkles release spray works on curtains. Wrinkle release spray is the simplest and quick way to get wrinkles or creases out of curtains. Even you can do this in a minute.
When you spray the wrinkle release spray on the curtains, the spray relaxes the fabric and makes them straighten on their own. This will disappear the crease and wrinkles from the fabric.
You have to spray the wrinkle release spray from a 10 inches distance. The wrinkles will damp after getting the spray. Then you have to pull the curtain downwards straight. After a couple of minutes, you will notice the curtain is wrinkle-free.
What materials make wrinkle-free blackout curtains?
Blackout curtains sometimes get wrinkles. These wrinkles are not so easy to remove. Because blackout curtains are made of a different fabric than others. So, some materials that are wrinkle-free are suitable to make blackout curtains.
Some wrinkle-free fabrics are wool, lyocell, Tencel, polyester, cashmere, knit, spandex, etc. These fabrics don’t get wrinkles easily. So, if blackout curtains can be made of these fabrics, they will be wrinkle-free.
How to get deep wrinkles out of curtains?
Curtain’s wrinkles can be removed by different methods. Iron, steam, wash and dry, humidity, etc., methods are common to get the wrinkles out of curtains. But if the wrinkles are deep or stubborn, these processes might not work.
You have to use wrinkle release spray to get deep wrinkles out of curtains. You can also combine two of the previous process to remove deep wrinkles.
For example, you have to wash the curtains in the washing machine and dry them in the dryer. Then you have to iron the curtains. These two combined processes will remove all the wrinkles from the curtains. Even deep and stubborn wrinkles and creases will go away.
Is it better to steam or iron blackout curtains?
Steaming blackout curtains is better than iron. Steaming make the blackout curtains wrinkle and crease-free. Moreover, steaming will make the fabric richer with a natural look. Steaming is also easy and safe to use on fabric. You don’t have a fear of burning the fabric with steam.
Contrarily, ironing might damage the fabric. The high heat of the iron isn’t safe for all materials of blackout curtains. Moreover, ironing might not keep the natural look of the fabric. So, steaming is preferable to ironing blackout curtains.
Wrinkles or creases make the blackout curtains look dull. The whole appearance of the room might change because of wrinkles or creases on the curtains. So, you have to get wrinkles out of the curtains.
You can follow different methods. But ironing, steaming, drying is the most common and easy methods to remove wrinkles from fabrics. But you have to be careful while using iron on the blackout curtains. However, removing creases or wrinkles isn’t that difficult if you follow the process properly.